Powermatic COS18 Manual de usuario

OWNER’S MANUAL Model COS18 Cut-Off Saw Left-Hand model shown, with 8' and 4' optional roller tables

10ELECTRICAL CONNECTIONS WARNING: Electrical connections must be made by a qualified electrician in compliance will all relevant codes. The

11DUST COLLECTION Powermatic recommends the use of a dust collection system with this cut-off saw. The collector should have sufficient capacity (60

127. Re-install clear panel and close blade access door, fastening it securely. NOTE: A sensor switch on the door will automatically shut down the s

13To mount roller tables to saw: 1. Mount an angle bracket to the pre-drilled holes in the side of the saw cabinet with four M8 x 20 hex cap screws

148-FOOT TABLE GUIDE 1. The 8-foot table comes with a guide and scale. The guide should be mounted to the edge of the table with six M8 x 27 square

155. Now place the board flush against the fence and against the rail of the roller table(s). If necessary, shift a roller table horizontally to bri

16BELT REPLACEMENT 1. Release tension on the v-belt and remove old belt. 2. Make sure the new belt is properly situated into the v-grooves of th

17OPTIONAL ACCESSORIES - COS18 Cut-Off Saw Part No. Description 6827037 ... 8' Roller T

18PARTS LIST: Table & Motor Assembly (COS18 Cut-Off Saw) Index Part No. No. Description

19PARTS LIST: Table & Motor Assembly (COS18 Cut-Off Saw) continued Index Part No. No. Description

2 This manual has been prepared for the owner and operators of a Powermatic Model COS18 Cut-Off Saw. Its purpose, aside from proper machine operation

20Table & Motor Assembly – Left Hand (COS18 Cut-Off Saw)

21Table & Motor Assembly – Right Hand (COS18 Cut-Off Saw)

22PARTS LIST: Stand Assembly (COS18 Cut-Off Saw) Index Part No. No. Description

23Stand Assembly – Left Hand (COS18 Cut-Off Saw)

24Stand Assembly – Right Hand (COS18 Cut-Off Saw)

25PARTS LIST: Air Control Assembly (COS18 Cut-Off Saw) Index Part No. No. Description

26Air Control Assembly – Left Hand (COS18 Cut-Off Saw)

27Air Control Assembly – Right Hand (COS18 Cut-Off Saw)

28PARTS LIST: Safety Guard Assembly (COS18 Cut-Off Saw) Index Part No. No. Description

29PARTS LIST: Safety Guard Assembly (COS18 Cut-Off Saw) continued Index Part No. No. Description

3TABLE OF CONTENTS Safety Rules...

30Safety Guard Assembly – Left Hand (COS18 Cut-Off Saw)

31Safety Guard Assembly – Right Hand (COS18 Cut-Off Saw)

32PARTS LIST: 4' Roller Table Assembly (COS18 Cut-Off Saw) #6827038 Optional Accessory Index Part No. No.

334' Roller Table Assembly (COS18 Cut-Off Saw) #6827038 Optional Accessory

34PARTS LIST: 8' Roller Table Assembly (COS18 Cut-Off Saw) #6827037 Optional Accessory Index Part No. No.

358' Roller Table Assembly (COS18 Cut-Off Saw) #6827037 Optional Accessory

36PARTS LIST: Pneumatic Diagram (COS18 Cut-Off Saw) Index Part No. No. Description

37PARTS LIST: Pneumatic Diagram (COS18 Cut-Off Saw) continued Index Part No. No. Description

38ELECTRICAL SCHEMATIC (COS18 Cut-Off Saw)

39Preventive Maintenance Checklist for Model COS18 Cut-Off Saw [ ] Work area around machine marked off clearly. [ ] Non-skid floor strips in

4 SAFETY RULES As with all machines, there is a certain amount of hazard involved with the use of this cut-off saw. Use the machine with the respect

40 WMH Tool Group 427 Sanford Road LaVergne, TN 37086 Phone:(800) 248-0144 Fax: (800) 274-6840 E-mai

5Job completion. If the operator leaves the machine area for any reason, the cut-off saw should be turned "off" and the blade should come

6 SAFETY Familiarize yourself with the location and content of these decals on your machine. FIGURE 1

7SPECIFICATIONS: COS18 Cut-Off Saw Stock number (COS18L)...

8FEATURES: COS18 Cut-Off Saw FIGURE 2

9RECEIVING Open shipping crate and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Before using t